moodLearning Wiki

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

troubleshooting-elib-box [2018/12/08 09:29]
serbizadmin [Raspberry Pi 3 with Raspbian Stretch]
troubleshooting-elib-box [2020/06/13 15:10]
Line 1: Line 1:
-====== Troubleshooting eLib Box ====== 
-===== Ethernet not working ===== 
-====Raspberry Pi 3 with Raspbian Stretch==== 
-  * confirm 
-<code> 
-ifconfig -a 
-</code> 
-may include something like this 
-<code> 
-eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500 
-        ether b8:27:eb:2c:94:19  txqueuelen 1000  (Ethernet) 
-        RX packets 0  bytes 0 (0.0 B) 
-        RX errors 0  dropped 0  overruns 0  frame 0 
-        TX packets 0  bytes 0 (0.0 B) 
-        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0 
-</code> 
- or do 
-<code> 
-sudo service dhcpcd status 
-</code> 
-and you'll have something like this 
-<code> 
-systemd[1]: Starting dhcpcd on all interfaces... 
-dhcpcd[330]: Not running dhcpcd because /etc/network/interfaces 
-dhcpcd[330]: defines some interfaces that will use a 
-dhcpcd[330]: DHCP client or static address 
-systemd[1]: dhcpcd.service: Control process exited, code=exited status=6 
-systemd[1]: Failed to start dhcpcd on all interfaces. 
-systemd[1]: dhcpcd.service: Unit entered failed state. 
-systemd[1]: dhcpcd.service: Failed with result 'exit-code'. 
-</code> 
-  * inject 
-<code> 
-ifconfig eth0 192.168.1.66 <or some appropriate number on the dhcp network> 
-</code> 
-  * adjust dhcp via /etc/dhcpcd.conf 
-<code> 
-static domain_name_servers=172.24.1.1 192.168.1.1 
-</code> 
-Adjust the latter according to the appropriate number for the eth0 network. 
-  * confirm  
-<code> 
-hostname -I 
-</code> 
-\\ 
  
-===== Raspberry Pi 3 Model B+ does not boot ===== 
-If these conditions obtain: 
-  * booting for the first time on this hardware 
-  * using the Raspian OS upgraded on Raspberry Pi 3 Model B (without the +) 
-then it's likely that the boot disk doesn't contain the requisite firmware. So upgrade NOOBS. 
-  * Download [[http://downloads.raspberrypi.org/NOOBS/images/NOOBS-2018-03-14/NOOBS_v2_7_0.zip|this NOOBS version]] 
-  * mount 1 partition of the SD card 
-<code> 
-sudo mkdir -p /media/pi/MMC_P1 
-sudo mount -t vfat /dev/mmcblk0p1 /media/pi/MMC_P1 
-</code> 
-  * delete contents of partition 1 
-<code> 
-sudo find /media/pi/MMC_P1 -mindepth 1 -delete 
-</code> 
-  * unzip NOOBS into partition 1 
-<code> 
-sudo unzip /home/pi/NOOBS_v2_7_0.zip -d /media/pi/MMC_P1 
-</code> 
-  * remove //runinstaller// 
-  * sudo nano /media/pi/MMC_P1/recovery.cmdline 
-With //runinstaller// removed, the line should look like this 
-<code> 
-quiet ramdisk_size=32768 root=/dev/ram0 init=/init vt.cur_default=1 elevator=deadline 
-</code> 
-  * shutdown 
-\\ 
-\\ 
-==== References ==== 
-  * [[https://www.raspberrypi.org/forums/viewtopic.php?f=63&t=212452|"Update NOOBS without Re-Installing It (When Your Raspberry Pi 3B+ Will Not Boot!)"]] 
-  * [[https://www.raspberrypi.org/forums/viewtopic.php?t=209638|Using an SD card from PI 3 MODEL B in PI 3 MODEL B+]]